Power supply
Last updated
Last updated
IDU-CPE-G(24W) is an indoor Gigabit PoE injector which supports 100-240 V input range from the AC mains. IDU-CPE-G(24W) feeds 48 VDC power to the device by injecting it to the CAT5 Ethernet cable.
Compatible models
Astra Quanta and Astra Evolution (except E5-BSQ), AUX-ODU-SYNC
Size and weight
9753.533.5 mm, 0.133 kg
Connectors and Interfaces
"LAN" - Ethernet input (Data only)
"POE" - Ethernet output (Data+VDC), PASSIVE PoE
"PWR" - AC Input
Supported Ethernet Modes
10/100/1000 Mbps
Standards
IEEE 802.3 10Base-T
IEEE 802.3U 100Base-TX
IEEE 802.3ab 1000Base-T
Input Power Requirements
AC Input Voltage: 100 ... 240 VAC
AC Input Current: 0.75 A
AC Frequency: 50 to 60 Hz
Consumption
28 W
Operating temperature range
-10 °С ... +40 °С
Operating humidity
Maximum 95 %, Non-condensing
Storage temperature
-40 °С ... +70 °С
Output Power Voltage
48 VDC, 0.5 A
Safety
UL cUL, CE, GS, CCC, FCC, S-MARK, PSE, C-tick, KC(48V0.5A) BIS（24V1A
1
A+
A+
2
A-
A-
3
B+
B+
4
C+
C+
5
C-
+VDC/ C-
6
B-
B-
7
D+
-VDC / D+
8
D-
-VDC / D-
IDU-CPE-G(56W) is an indoor AC/DC PoE injector with built-in lightning protection. PoE injector is powered by an AC supply in the 100-240 V range.
Compatible models
Astra Quanta, Astra Evolution
Connectors and Interfaces
"LAN" - Ethernet input (Data only)
"POE" - Ethernet output (Data+VDC), PASSIVE PoE
"PWR" - AC Input
Consumption
60 W over 4-pairs (Guaranteed)
EMC
Meet:
FCC Part 15, Class B
Input Voltage
100 ... 240 V
Lightning Protection
In compliance with:
IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact)
IEC 61000-4-4 (EFT) 40A (tp = 5/50ns)
IEC 61000-4-5 (Lightning) L5, 95A (tp = 8/20us)
Operating temperature range
0 °С ... +40 °С
Output Voltage & Current
+56 V, 1 A
Pin Assignment and Polarity
1/2 (+) and 3/6 (-)
4/5 (+) and 7/8 (-)
Size
137.5*62.5*33 mm (L*W*H)
Supported Ethernet Modes
10/100/1000Mbps (Gigabit Ethernet pass-through)
Weight
0.24 kg
IDU-LA-G(V.01) is an indoor DC/DC injector. It greatly reduces complexity of the deployment in the cases where DC source is available thus reducing both capital expenditures and total cost of ownership.
IDU-LA-G(V.01) may be used for the following purposes:
To serve as a line protection unit for indoor network equipment connected to the second Ethernet port on ODU.
To connect third-party DC power sources to ODU (for example, to power the unit from solar power or wind power sources).
Compatible models
Astra Quanta, Astra Evolution
Output Voltage
The same as input
Supported Ethernet Modes
10/100/1000 Mbps (Gigabit Ethernet pass-through)
Pin assignment and polarity
1/2 (+), 3/6 (-), 4/5 (+), 7/8 (-)
Size and Weight
115×65×40 mm, 0.15 kg
Operating temperature range
From 0°С to +40°С
CAUTION
Exposing unit to the unsupported voltage will result in irreparable damage to the unit! Always observe power requirements!
Optional indoor/outdoor DC injector with built-in lightning protection. It greatly reduces complexity of the deployment in the cases where DC source is available on the rooftop eliminating the need of weather-sealed cabinets. AUX-ODU-INJ-G is compatible with all Astra Wireless devices.
Size and Weight
34x94x121 mm, 0.28 kg
Connectors and Interfaces
ETH IN - Ethernet input
ETH OUT - Ethernet output (data+VDC, protected leg)
PWR - DC Input
GND - Ground clamp
Supported Ethernet Modes
10/100/1000 Mbps (Gigabit Ethernet pass-through)
Water and Dust Protection
IP66 and IP67
Operating temperature range
-55 °C ... +60 ºC
DC Range
±43...±56 VDC
Lightning Protection
In compliance with:
GR-1089
IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact)
IEC 61000-4-4 (EFT) 40A (tp = 5/50ns)
IEC 61000-4-5 (Lightning) L5, 95A (tp = 8/20us)
ETSI ETS 300 386
CAUTION
Using inappropriate DC source will damage the ODU, which will be not covered by warranty
1
Data pair A+
Data pair A+
2
Data pair A-
Data pair A-
3
Data pair B+
Data pair B+
4
Data pair C-
+VDC + Data pair C-
5
Data pair C+
+VDC + Data pair C+
6
Data pair B-
Data pair B-
7
Data pair D+
-VDC + Data pair D+
8
Data pair D-
-VDC + Data pair D-
AUX-ODU-INJ-G is supplied with a worm clamp TORRO 40-60/9 C7 W4 DIN 3017 - 2 pcs. The clamp is made of stainless steel A4, width 9 mm, allows the installation on a mast with a diameter of 35 to 60 mm. In case of mast diameter more than 60 mm, a similar clamps (up to a 230 mm diameter) with a width of up to 12-13 mm can be used.
