Astra Wireless Documentation
  • Technical documentation
    • Astra Quasar Technical User Manual
      • Introduction
        • Key Features⁣⁣⁣⁣⁣
        • Hardware Platform
        • Power supply⁣⁣⁣⁣⁣⁣⁣
        • Lightning protection unit⁣⁣⁣⁣⁣⁣⁣⁣⁣⁣⁣
        • Packing List
      • Planning considerations⁣⁣⁣⁣⁣⁣⁣⁣⁣
      • Link Pre-configuration in the lab⁣⁣⁣⁣⁣⁣⁣⁣⁣
      • Installation⁣⁣⁣⁣⁣
      • Operation & Administration⁣⁣⁣⁣⁣
        • Web GUI access⁣⁣⁣⁣
        • Dashboard⁣⁣⁣⁣
        • General settings⁣⁣⁣⁣⁣
        • Security settings⁣⁣⁣⁣
        • Radio Settings
        • Switch settings
        • MINT Settings
        • SNMP settings
      • Services
        • Maintenance
    • Astra Quanta⁣ Technical User Manual
      • Introduction⁣⁣⁣⁣⁣⁣⁣
        • Key Features⁣⁣⁣⁣⁣
        • Hardware Platform⁣⁣⁣⁣⁣
        • Power Supply⁣⁣⁣⁣⁣⁣
        • Lightning⁣ ⁣protection unit⁣⁣⁣⁣⁣
        • Packing list⁣⁣⁣⁣⁣⁣⁣
      • Planning considerations⁣⁣⁣⁣⁣⁣⁣
      • Link pre-configuration in the lab⁣⁣⁣⁣⁣
      • Installation
      • Operation & Administration⁣⁣⁣⁣⁣
        • Web GUI access⁣⁣⁣⁣
        • Dashboard⁣⁣⁣⁣
        • General settings⁣⁣⁣⁣⁣
        • Security settings⁣⁣⁣⁣
        • Radio settings⁣⁣⁣⁣
        • Network settings⁣⁣⁣⁣⁣
        • Switch Settings
        • SNMP settings⁣⁣⁣⁣
        • Spectrum Analyzer⁣⁣⁣⁣⁣
        • Antenna Alignment Tool⁣⁣⁣⁣⁣
        • Maintenance⁣⁣⁣
        • Instant DFS⁣⁣⁣⁣
        • Graphs⁣⁣⁣⁣
      • Troubleshooting⁣⁣⁣⁣⁣⁣⁣⁣⁣
    • Astra Evolution Technical User Manual
      • Introduction⁣⁣⁣⁣⁣⁣
        • Key Features⁣⁣⁣⁣⁣⁣⁣
        • Hardware Platform⁣⁣⁣⁣⁣⁣⁣⁣
        • Power supply⁣⁣⁣⁣⁣⁣⁣
        • Lightning protection unit⁣⁣⁣⁣⁣⁣⁣⁣⁣⁣⁣
        • Synchronization unit⁣⁣⁣⁣⁣⁣⁣
        • ⁣⁣⁣Packing List
      • Planning considerations⁣⁣⁣⁣⁣⁣⁣⁣⁣
      • Link Pre-configuration in the lab⁣⁣⁣⁣⁣⁣⁣⁣⁣
      • Installation⁣⁣⁣⁣⁣
      • Operation & Administration⁣⁣⁣⁣⁣⁣⁣
        • Web GUI access⁣⁣⁣⁣⁣⁣
        • Device Status⁣⁣
        • Basic Settings⁣⁣⁣⁣⁣
          • System Settings⁣⁣⁣⁣⁣⁣
          • Network Settings⁣⁣⁣⁣⁣⁣⁣
          • Link Settings⁣⁣⁣⁣⁣⁣
          • Static Links⁣⁣⁣⁣⁣
          • MAC Switch⁣ ⁣
          • IP Firewall
          • SNMP
          • QoS Options⁣⁣⁣⁣⁣⁣
          • Traffic Shaping⁣⁣⁣⁣⁣⁣⁣
          • Extra Commands⁣⁣⁣⁣⁣⁣
        • Maintenance
        • Spectrum Analyzer
        • DFS
        • Command Line
      • Troubleshooting⁣⁣⁣⁣⁣⁣
        • No access to the local unit⁣⁣⁣⁣⁣
        • The wireless link cannot be established⁣⁣⁣⁣⁣
        • The wireless link is established, but there is no access to the remote device⁣⁣⁣
        • The wireless link throughput is lower than expected⁣⁣⁣
        • Common errors in configuration⁣⁣⁣⁣
        • Emergence Repair Console⁣⁣
        • Unicast-flood detection⁣⁣⁣⁣
    • AstraFleX⁣ Technical User Manual
      • Getting started with AstraFleX User Manual
      • ⁣⁣IP-address format
      • General Purpose Command Set
      • Layer 2 commands set -PHY and MAC
        • ⁣prf ⁣command
        • ⁣⁣lag command (Link Aggregation )
        • ⁣⁣svi command
        • ⁣⁣ltest (radio link test)
        • macf command (addresses mapping)
        • ⁣⁣arp command (ARP protocol)
        • ⁣⁣switch command
        • ⁣⁣dfs (Dynamic Frequency Selection)
        • ⁣⁣lldp command
        • ⁣⁣mint command
        • ⁣⁣rfconfig command
      • ⁣⁣Layer 3 Command set – IP Networking
        • ⁣⁣Ifconfig command (interfaces configuration)
        • tun command (tunnels building)
        • qm command (QoS configuration)
        • ⁣⁣route command (static routes configuration)
        • ⁣⁣arip command
        • ⁣⁣OSPF command
        • ARDA (Aqua Router DAemon)
        • ⁣⁣netstat command (Network statistics)
        • ⁣⁣ipfw command (IP Firewall)
          • ⁣⁣PCAP-filters
        • ⁣⁣loadm command (load meter)
        • ⁣⁣rpcapd command (Remote Packet Capture)
        • ⁣⁣snmpd command (SNMP daemon)
        • ⁣⁣td command (Telnet daemon)
        • ⁣⁣nat command (Network Address Translation)
        • ⁣⁣trapd command (SNMP Traps support)
        • dhcpd command (DHCP Server)
        • ⁣⁣dhcpr command (DHCP relay)
        • dhcpc command (DHCP Client)
        • ⁣⁣vrrp command (VRRP server)
      • ⁣⁣Other commands
    • ⁣NEXT Monitoring System Technical User Manual
      • Description⁣ and operational principles
      • Installation
      • Configuration⁣⁣ ⁣and⁣ management⁣
        • Wireless⁣ ⁣⁣devices preparation
        • Accounts⁣ and user groups
        • Devices⁣ ⁣and links
        • Incident⁣ ⁣⁣management
        • System⁣⁣ ⁣configuration
      • Monitoring⁣ ⁣and management
        • R⁣ep⁣o⁣⁣rts
        • Devices
        • ⁣⁣Incidents
        • MAP
      • Technical support
  • White⁣ papers
    • MINT ⁣⁣⁣technology
    • Dynamic ⁣⁣Frequency ⁣⁣Selection
    • ⁣⁣RADIUS authentication for admin users
    • Security in Astra Wireless Devices
    • ⁣⁣Performance of the Astra Wireless devices
      • Astra Quanta
        • ⁣⁣Thr⁣⁣⁣oughpu⁣t⁣⁣⁣⁣⁣⁣
        • ⁣Packet ⁣⁣performanc⁣e⁣⁣⁣⁣⁣
      • Astra Evolution
        • H22 platform
          • Packet ⁣⁣⁣perfor⁣mance⁣⁣
          • Throug⁣hput⁣⁣⁣⁣⁣⁣
        • H16 platform
          • Packet⁣⁣ ⁣perfor⁣mance⁣⁣
          • ⁣⁣⁣⁣⁣⁣Throug⁣hput⁣⁣⁣⁣⁣⁣⁣
    • ⁣⁣⁣Link ⁣⁣⁣aggregation, balancing and redundancy
      • Astra Evolution
        • Redundancy ⁣⁣⁣with Failover option
        • Redundancy w/o aggregation and AstraMUX
        • Redundancy⁣⁣⁣ ⁣with aggregation and w/o AstraMUX
        • Redundancy ⁣⁣with AstraMUX
        • Full⁣ Duplex
      • Astra Quanta
        • Aggregation ⁣with redundancy ⁣based on⁣ LACP
        • Redundancy⁣⁣⁣ ⁣based ⁣on STP
        • ⁣Redundancy⁣⁣ based on⁣ OSPF
        • ⁣Redundancy with Evolution
    • Beamforming⁣ ⁣technology
    • ⁣⁣⁣Remote ⁣⁣⁣L2 management of Evolution via CLI
    • ⁣⁣⁣Remote ⁣⁣⁣L2 management of Evolution via Web GUI
    • Connectivity with mobile objects⁣⁣⁣⁣
      • Mining industry⁣⁣⁣
      • Railway transport⁣⁣⁣
      • Transport over the water⁣⁣⁣
      • Configuration example⁣⁣⁣
Powered by GitBook

Astra Wireless Technology © 2024. All rights reserved. For more information about available models, sales and technical support, please proceed to https://astrawireless.net/

On this page
  • Description
  • Parameters
  • Examples
  1. Technical documentation
  2. AstraFleX⁣ Technical User Manual
  3. Layer 2 commands set -PHY and MAC

⁣⁣svi command

Description

SVI interface is a virtual L3 interface. Can be assigned to a switch group to provide the device management using this switch group. Each unit supports 5000 virtual "sviN" switch interfaces (in range 0...4999).

An SVI interface has the following characteristics:

  • Each SVI interface can be assigned to a switch group. Once assigned the interface becomes an active member of that switch group and can exchange traffic with other group members. All traffic ingressed by this switch group (depending on the rules set) that is addressed to this SVI interface as well as all broadcast and multicast packets will be processed by the unit.

  • Each SVI interface can have one or several IP addresses configured.

  • An SVI interface can act as a parent interface for VLAN virtual interfaces. In this case the VLAN interface also becomes a member of the switch group assigned to the parent SVI interface - not recommended.

  • An SVI interface (or any other interface that uses it as a parent interface) can not be included into a switch group directly.

  • An SVI interface can be used for channel aggregation using lag interfaces..

  • An SVI interface is considered active once it is up and assigned to a switch group.

Following command allows to create the SVI interface and assign an IP address to it:

ifconfig sviN IP_ADDR up

NOTE

In order to set communication with other devices via protocols, that utilize the broadcast/multicast packets (such as OSPF, RIP, DHCP) use one of two options:

  • Use only the IP address assigned to the SVI interface, if the traffic enters a switch group that has an SVI interface.

  • It is possible to use the IP address assigned to the physical interface (radio or Ethernet), if this interface is not included in the switch group, or there is no SVI interface in the switch group.

Otherwise, communication between the devices will not be established.

Syntax:

svi N group G [addpri|setpri N|-1]
svi N clear

Parameters

Parameter
Description

N

Identifier of the SVI interface to configure.

group G

Assigns specified SVI interface to the switch group.

  • "G" – switch group identifier.

[addpri|setpri N|-1]

Allows to provide priority management.

  • "setpri N" – sets the packet priority with the value "N".

  • "-1" – resets the priority.

  • "addpri" – changes the priority only if new is higher than already available for the package. Thus, the "addpri" parameter allows only to increase the priority.

clear

Removes SVI interface settings.

Examples

Set the priority 5 for all the packets passing through the "svi1" interface.

svi 1 setpri 5

Assign "svi100" interface to switch group # 100.

svi 100 group 100
Previous⁣⁣lag command (Link Aggregation )Next⁣⁣ltest (radio link test)

Last updated 1 year ago